How to Build a Shadowbox Fence | The Home Depot

how to build a shadow box fence This is a topic that many people are looking for. cfiva.org is a channel providing useful information about learning, life, digital marketing and online courses …. it will help you have an overview and solid multi-faceted knowledge . Today, cfiva.org would like to introduce to you How to Build a Shadowbox Fence | The Home Depot. Following along are instructions in the video below:
Shadowbox fence is also known as a neighbor friendly fence because it provides the same same look on both sides. Once the posts have been set rails can be toenail the posts in this video. Well be installing the fence on fairly level ground but if youre installing the fence on sloped terrain you have two options the rails can be installed following the slope and kept a consistent distance from the ground or you can use a stepped approach and keep the rails level throughout after the rails have been installed the pickets can be installed to the rails.
Leaving a gap between each picket. A 2×4 used as a spacer works well when installing standard six inch wide pickets when installing pickets of a smaller width leave a smaller gap on the reverse side of the fence. You will install the pickets.
The same way. But with each picket filling the gaps left on the other side. The result is a fence that provides some privacy for both you and your neighbor.
While allowing light and air to pass through the fence an alternate method is to install the pickets with the same gap. But closing these gaps by installing a second layer of pickets on the same side of the fence. This board on board approach will provide more privacy.

how to build a shadow box fence-0
how to build a shadow box fence-0

But one side of the fence will have a post and rail views before installing any fence check your local government for any zoning issues and find out if there are any frost line requirements in your area also call 8 1. 1. To have your local utility providers mark.
Any underground lines or pipes. Good luck and thanks for shopping at the home depot. As with all fencing projects planning out the fence line and the post positions is the key to a strong straight fence begin by driving stakes into the ground.
Where you plan to set your end and corner posts. Once theyre set tie a masons line around one stake and unfurl it down. The planned fence line and tie.
It off on the opposite end stake pull the line taut before tying it off this will be your guide when digging the holes for the posts and for the bottom of the pickets adjust the line. So its at least three inches off the ground to prevent wood rod mark. The placement for your first post out from the masons line.

how to build a shadow box fence-1
how to build a shadow box fence-1

This will enable you to dig the hole without disturbing. The guideline. When the posts are positioned.
Youll need to measure out from this line to the post and keep the distance consistent. This will result in a straight fence line measure and mark the position for the next post eight feet out from the first post. This will allow for the 8 foot 2×4 rails to be trimmed and installed between the posts when digging the holes for the posts.
Always dig them two to three times the width of the post and to a depth 1 3. To 1 2. The posts length when setting wood posts.
Its best to dig down an additional six inches to allow for gravel backfill this gravel will help drain water away from the base of the post which will help prevent rotting in colder climates you may need to dig down below the frost line to guard against frost heave. When constructing wood fences always choose pressure treated pine redwood or cedar posts because their rot resistant. When installing a rail and picket fence.

how to build a shadow box fence-2
how to build a shadow box fence-2

The post holes can be dug all at once with either a post hole digger or a gas powered auger augers are available for rent at most home depot store locations and can be a real time saver when adjusting for a changing slope and turns in the fence line mark. Each new fence line section with stakes and masons line for more detailed information on setting posts. Please watch our installing fence post video at video home depot.
Comm and click on the fencing section. Once all the holes have been dug and back filled with gravel. You can begin to set the posts with the help of an assistant adjust each post as you set it until its plumb and then brace it on two sides with a two by four attached to a stake in the ground once properly braced posts can be set in concrete.
Its recommended that all corner and and gate posts be set in concrete for added stability for the strongest possible fence set the line posts and concrete as well when constructing a long fence line set several posts at once and then reuse the braces as you work your way down the fence line mark. The inside edge of the post 12 inches up from the ground this line is where the top of the bottom rails will be placed mark down 12 inches from the top of the posts. This is where the bottom of the upper rail will be installed begin by installing the bottom rail.
Then the top and middle to find the position for the middle rail measure the distance between the top and bottom rails and divide by two the middle rail should be installed on this line on center each rail should be toenail din to the posts with the narrow side of the 2×4 facing out and flush with the post tow. It in on both sides using 3 inch galvanized deck screws move. The masons line you used as a guide for setting the posts to the edge of the set posts adjust the height of the masons line to be a consistent height from the ground this line will serve as a guide for the bottom of the pickets as you install them the pickets should be at least two inches off the ground to prevent wood rod starting at one end post position.

how to build a shadow box fence-3
how to build a shadow box fence-3

The first picket aligned with the mason string check that this first picket is plumb and flush with the outside edge of the post. Then drive to evenly spaced two inch wood screws into each rail for installing subsequent pickets. Its best to use a spacer to maintain the proper distance between pickets.
A 2×4 with a piece of scrap wood attached. Works well for this the scrap block will allow you to hang the spacer on the top rail. Freeing up both hands slide.
The spacer up flush against the last install picket and but the next pick it up against the spacer. Attaching the level to the spacer will allow you to check the pickets for plumb. As you work your way down the fence line.
Once the pickets are installed on one side of the fence you can begin installing them on the other if youre building a shadowbox fence install them filling the gaps on the other side if you prefer a privacy fence install the pickets on the same side covering the gaps with a board on board technique. If youre ready to take on this project. Here are the tools and materials youll need to complete the job when properly maintained would fences can last for many years to help prolong the life of your fence.
It should be cleaned and sealed periodically before applying a protective sealant clean the fence with a product that kills mildew. As well as remove stains once dry apply a high quality protective sealant. According to the manufacturers instructions and be sure to coat all exposed surfaces.
.

how to build a shadow box fence-4
how to build a shadow box fence-4

Thank you for watching all the articles on the topic How to Build a Shadowbox Fence | The Home Depot. All shares of cfiva.org are very good. We hope you are satisfied with the article. For any questions, please leave a comment below. Hopefully you guys support our website even more.

Leave a Comment

Your email address will not be published. Required fields are marked *